Installation & OperatingManualE400 WirefreeAlarm System

House Code is set up by moving each of the first 8 switches(numbered 1-8) to a random sequence of ‘ON’ or ‘OFF’.Note: when setting the miniature swit

2. The system is now in Test/Programming mode.3. Now, each time the Control Unit receives a validradio signal from a detector or Remote Control, theCo

Before selecting a position for a Passive Infra RedMovement Detector the following points should benoted:1. Do not position detector facing a window o

The recommended Pulse Count is one. In cases ofextreme environmental problems or if unattributablefalse alarms are experienced, it may be necessaryto

6. Slide the batteries supplied into the battery holder,ensuring that the positive (+) side is uppermost oneach battery as it is installed.7. Carefull

roof overhangs should also be avoided. Where applicable,the Solar Siren & Strobe should be positioned a minimumof twice the width of the eaves ov

ALARM DURATIONThis is the maximum length of time that the Solar Siren &Strobe alarm will sound for, following activation. Alarmduration can be se

The Control Unit LEDs 1-8 will indicate the new HouseCode switch setting eg.Press to memorise the House Code setting and torevert to the Test/P

With the Control Unit in Test/Programming modeEnterA Zone LED will illuminate to indicate the setting:-(factory default 3 minutes - Zone 3 LED ‘ON’).

8. USER ACCESS CODEThe Control Unit is supplied with a preset User AccessCode of . This code allows generaloperation (Arming/Disarming etc) and pr

FOREWORDYour decision to purchase an Eclipse E400 WirefreeAlarm System represents a major and sensible steptowards total protection of your premises,

Details of Control Unit Terminal BlockOPERATINGINSTRUCTIONSFULLY ARMING THE SYSTEMWhen leaving the premises, the system must be FullyArmed. However,

DISARMING THE SYSTEMUpon entering an Entry Delay Zone, the appropriateZone LED(s) will illuminate and the Control Unitsounder will either emit a const

TESTING THE SYSTEMYou may test your system at any time, however, it isrecommended that the system is tested at regularintervals not exceeding three mo

E400 ALARM RECORDComplete the following information during installation for future reference.Zone Detector Type(s) Location(s)SettingsInstant/Delay Pa

TROUBLE SHOOTINGControl Unit not working. Mains light is off1. Press key on Control Unit. If mains light illuminatesand then extinguishes after

TROUBLE SHOOTING - continuedPassive Infra Red Movement Detector notdetecting a person’s movement1. Allow up to one minute for the detector to settledo

EXTENDING YOUR ECLIPSE E400 WIREFREEINTRUDER ALARM SYSTEMYou may add additional Remote Controls, Wirefree Magnetic Contact Detectors and Wirefree PIR

ResponseE400 Wirefree Alarm SystemGUARANTEEThis product (excluding Alkaline batteries) is guaranteed for one year fromthe date of purchase against fau

Control Unit●Four Wirefree Programmable Zones●Integral 105dB Siren●Two Siren Tones - Intruder and Tamper/Personal Attack●Zones programmable for:- Entr

CONTENTSPage No.FOREWORD Inside Front CoverINTRODUCTION AND OVERVIEW 2PLANNING AND EXTENDING YOUR E400WIREFREE ALARM SYSTEM 4CONTROL UNITIndicators an

INTRODUCTION AND OVERVIEWThe E400 Wirefree Alarm System is designed to allow flexibility in configuring and using the system.The detectors can be set

ZONE1234ON1234567890WP1.2-12WP1.2-6Detector and RemoteControl Batteries Also included:Installation and Operating ManualAll necessary fixings Window wa

For even greater protection you can install as manyPassive Infra Red Movement Detectors and MagneticContact Detectors as and when you require. The E4

LOCATIONWhen choosing a suitable location for the Control Unit,the following points should be considered.1. Ensure that the Control Unit is within a p

INSTALLATION1. Undo the two front cover retaining screws and hingethe Control Unit cover down. Remove the ControlUnit Back-up Battery.2. Hold the Con

MAINS ADAPTOR AND BACK-UPBATTERYA DC Mains Adaptor and cable and 1.2Ahr rechargeableBack-up Battery are supplied with the E400 equipment.The purpose o